感應門是一種能夠實現自動感應識別開關功能的感應門。其原理是通過內部感應探測器檢測是否有人進入，結構合理的手術室感應門，為醫院和實驗室提供了大大的便利。感應門的使用需要達到良好的效果，這不僅與它的質量有關，還與它的安裝有關。如果安裝不正確，會導致后期出現很多問題。下面濟南感應門廠家為您分析：

Induction gate is a type of induction gate that can achieve automatic induction recognition switch function. The principle is to detect whether someone has entered through an internal sensing detector, and a structurally reasonable operating room sensing door provides great convenience for hospitals and laboratories. The use of induction doors needs to achieve good results, which is not only related to their quality, but also to their installation. If installed incorrectly, it can lead to many problems later on. Below is an analysis by the Jinan sensory door manufacturer for you:

一、安裝醫用感應門電機時，注意使之保持水平，保持誤差小于一毫米，如果不在一條水平線上會影響導致門體行走時沒有出現力道不均勻的現象，造成摩損嚴重，從而使之壽命不斷降低。

1、 When installing the medical induction door motor, pay attention to keeping it horizontal, with an error of less than one millimeter. If it is not on the same horizontal line, it will affect the phenomenon of uneven force path when the door body walks, causing serious friction damage and continuously reducing its lifespan.

二、手術室感應門吊架的安裝，使用所附的門吊架螺栓總成將吊架裝置安裝到門上的指定位置。安裝時，吊架裝置的滑輪中心應與門體平行。如果不平行，會縮短滑輪的使用壽命；同時懸掛裝置的滑輪懸掛在動力梁上，以免在安裝過程中損壞動力梁中的其他部件和導軌，否則會導致部件故障或滑輪壽命、噪音、異常聲音等。

2、 Install the operating room sensing door hanger using the attached door hanger bolt assembly to install the hanger device in the designated position on the door. When installing, the pulley center of the hanger device should be parallel to the door body. If not parallel, it will shorten the service life of the pulley; At the same time, the pulley of the suspension device is suspended on the power beam to prevent damage to other components and guide rails in the power beam during installation, otherwise it may cause component failure or pulley life, noise, abnormal sound, etc.

三、手術室自動感應門的限位裝置應安裝與限位裝置相一致的安裝螺栓。位置限制器裝置固定在動力梁的導軌上，移動門體固定門體位置后，位置限制器的位置固定。設置限位器位置時，懸掛裝置接觸限位器橡膠墊時應停止。

3、 The limit device of the automatic sensing door in the operating room should be installed with bolts that are consistent with the limit device. The position limiter device is fixed on the guide rail of the power beam. After moving the door body to fix the position of the door body, the position of the position limiter is fixed. When setting the position of the limiter, the suspension device should stop when it contacts the rubber pad of the limiter.

四、適當松開固定吊架的螺母，調整手術室感應門體的高度和間隙。調整螺栓和固定吊架的目的是確認行走時的阻力，確保門移動時沒有自重或摩擦聲。如果有問題，請確認門體上的掛鉤是否垂直固定。懸掛裝置是否與動力梁有摩擦。

4、 Loosen the nuts securing the hanger appropriately, and adjust the height and clearance of the operating room sensing door body. The purpose of adjusting the bolts and fixing the hanger is to confirm the resistance during walking and ensure that there is no self weight or friction sound when the door moves. If there are any issues, please confirm whether the hooks on the door body are vertically fixed. Is there friction between the suspension device and the power beam.

五、注意提高手術室感應門的皮帶張力調整。皮帶張力結構調整應保證將張緊輪裝置向左用力拉，使皮帶保持繃緊狀態。通過擰松手術室感應門的調節固定螺栓，沿順時針方向以及旋轉張力不斷調整螺栓，同時沒有擰緊四個方面調節板固定螺栓進而分析確定皮帶是否正確的張力。

5、 Pay attention to adjusting the belt tension of the operating room sensing door. The adjustment of the belt tension structure should ensure that the tensioning wheel device is forcefully pulled to the left to keep the belt in a tight and safe state. By loosening the adjusting fixing bolts of the operating room sensing door, continuously adjusting the bolts in a clockwise direction and rotating the tension, while not tightening the four adjusting plate fixing bolts, the correct tension of the belt can be analyzed and determined.

手術室感應自動門的安裝技巧相關內容就講解到這里了，希望能夠給您好的幫助，更多事項就來我們網站http://m.52yoga.net咨詢！

That's all for the installation techniques of the operating room induction automatic door. We hope to provide you with good help. For more information, please come to our website http://m.52yoga.net consulting service